DESCRIPTION
Auto Flip charcoal grill is composed of the following parts:
A. Charcoal grill (BZ5S) B. Electric Rotisserie (BZ5S) C. Auto Flip skewers (Z5TW)
Split structure, easy to clean, both parts can operate independently
A. Charcoal grill (BZ5S) is composed of the following parts:
A1 Charcoal grill body(stainless steel, thickness 1mm) A2 Grill net(Chrome plating) A3 Feet(4PCS) A4 Charcoal net (Chrome plating)
Quick to install without tools.
B. Electric Rotisserie (BZ5S) is composed of the following parts:
B1 Support plate (stainless steel) B2 Multi-function DC motor B3 Forks(stainless steel) with thumb screws(2PCS) B4 Extension rod(stainless steel) B5 Rotating rod(stainless steel) B6 Nylon Handle
It can be installed on the charcoal grill to automatic rotate roast whole chicken, roast fish, roast vegetables, etc. Quick to install without tools.
C. Auto Flip skewers (Z5) is composed of the following parts:
C1 Main engine Z5 (stainless steel) C2 Multi-function DC motor C3 Special needle Natural handle (30PCS) C4 Skewer support frame(stainless steel) C5 Fixed frame(with screws) C6 Guide rod(with screws)
It can be installed on the charcoal grill to automatic flip skewers. Quick to install without tools.
C. Auto Flip skewers (Z5TW) is composed of the following parts:
C1 Main engine Z5TW (stainless steel) C2 Multi-function DC motor C3 Special needle Natural handle (10PCS) C4 Skewer support frame(Z5TW) C5 Fixed frame(Z5TW) C6 Guide rod(with screws)
It can be installed on the charcoal grill to automatic flip skewers. Quick to install without tools.
DIMENSION
The length of the charcoal grill BZ5S is 48cm, the width is 28cm, the height is 13~19cm.
The distance between the two support plates is about 500mm, the height of the support plate is 200mm, the thickness is 2mm, and there are 3 heights that can be adjusted.
The length of the main engine Z5 is 420mm, the height is 120mm, and the distance between the skewers is 30mm.
The length of the main engine Z5TW is 420mm, the height is 120mm, and the distance between the skewers is 40mm, The distance between the upper skewers and the lower skewers is 30mm.
you need to bring your own bamboo skewers, but the diameter cannot exceed 6mm and the length is not less than 300mm.
SKEWERS SELECTION
If you want to buy more special needles, or want to use your own bamboo skewers with a diameter of less than 6mm or other baking needles with a diameter of less than 6mm for grilling, please click the link below to purchase.
MOTHER CLIP INSTALLATION
Before using for the first time, adjust the mother clip according to the size of your own bamboo skewers or other baking needles to be clamped (mother clip chuck fixed rotating handle or handle fixed rotating mother clip chuck). In the later use, just turn it clockwise to tighten it, and turn it counterclockwise to loosen it.
Note: Please wear BBQ Anti-scalding gloves when loading and unloading the baking needles
MULTI-FUNCTION DC MOTOR
MULTI-FUNCTION DC MOTOR
Specifications:
Condition: 100% Brand New
Material: Nylon + Metal
Main Color: White
No Load Current: Below 180MA
Output : 2~5RPM
Rotary Direction: CW
Voltage: DC 5V(With 1 meter USB wire)
Battery: 3pcs AAA batteries (not included)
Rotator Port : 0~5.0kgf.cm(0~11 lbs)
Roast Branch Size: 8 * 8mm / 0.32 * 0.32in
Motor Size: 6.8 * 6.8 *6.5cm / 2.7 * 2.7 * 2.6in
INSTALLATION STEPS
For Charcoal grill
Foot installation method 1
Use wing nut to install, you can adjust the appropriate height arbitrarily, tighten the wing nut to fix the foot.
Foot installation method 2
No wing nut is required for installation, only one height, Just tighten the feet directly.
So easy.
For Auto Flip skewers
Step1
Insert one of the threaded ends of the guide rod into any square hole on the back of the main engine unit as shown in the figure, and pass the round hole on the front.
Screw the wing nut clockwise to the thread of the guide rod, do not tighten it.
Install another guide rod in the other hole in the same way.
Step2
The other two guide rods are screwed clockwise to the other end of the installed guide rods as shown in the figure.
NORMAL MISALIGNMENT
NOTE: Thread processing needs to have a certain clearance, so it is difficult to have the same plane after the guide rod is tightened, and there will be a normal misalignment. At this time, you only need to loosen the guide rod a little, Make sure that the surfaces of the two guide rods are flush.
Step3
Pass the Skewer support frame and the Fixed frame through the guide rods in sequence as shown. Place the large end of the Fixed frame close to the charcoal grill while passing through the guides rod. Place the installed Auto Flip skewers on the charcoal grill.
Step4
Fix it on the charcoal grill body with 2 wing screws.
Step5
Adjust the position of the Skewer support frame and the Fixed frame according to the length of the skewers to ensure that the effective part of the skewers is above the fire in the charcoal grill and the other end of the skewers is in the slot of the Skewer support frame.
Step6
Tighten the thumb screws on the Fixed frame clockwise as shown.
Step7
Refer to motor installation instructions.
Step8
The installation is complete.
AUTO FLIP SKEWER MAINTENANCE
The Auto Flip Skewer is driven by a chain. After use, please wipe it clean and dry it and store it in a dry place. If possible, add chain oil to it to prevent the chain from rusting for a long time and cause transmission difficulties.
For Electric Rotisserie
Step1
Fix the support plate to the side plate of the Charcoal grill body with wing screws.
Note: The support plate is the same on both sides of the Charcoal grill body and cannot be installed in reverse.
Step2
Turn the Extension rod (B5) clockwise to the Rotating rod(B4), do not tighten, Screw the Nylon Handle(B6) to the Extension rod (B5) in the same way and tighten it.
Step3
The forks through the rod, screw the thumb screws to the forks. After loading the food, adjust it to the proper position and tighten the thumb screws.
NORMAL MISALIGNMENT
NOTE: Thread processing needs to have a certain clearance, so it is difficult to have the same plane after the guide rod is tightened, and there will be a normal misalignment. At this time, you only need to loosen the guide rod a little, Make sure that the surfaces of the two guide rods are flush.
Step4
Refer to step 3 place it in the proper height on the support plate to rotate.
Step5
Refer to motor installation instructions.
The installation is complete.
MOTOR WITHOUT BATTERY
The motor does not have a battery, you need to bring your own power bank or mobile phone charger for power supply. For the LED multi-function motor, you can also bring your own 3pcs AAA batteries (rechargeable batteries are not allowed) for power supply.
Because the motor is generally used in a high temperature environment, the built-in lithium battery is prone to explosion hazard.
About Power Bank
NOTE: Many power banks on the market have over-current protection functions. When the motor is used, the current passing through increases as the load increases. Once the allowable current is exceeded, the power bank will automatically cut off the power, which will cause the motor to stop, which is not the quality of the motor.
Free shipping to mainland China (except remote areas)
If you have a liaison office in mainland China，you can contact customer service online，in most areas，we can send the goods to your liaison office free shipping，You only need to click on the link below and submit the same quantity as the product price，and provide us with the detailed contact in mainland China.
